Close

Results 1 to 25 of 25
  1. #1
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322


    Yes Reputation No

    Preview of ESS Tuning S85 V10 (M5/M6) long tube headers designed specifically for forced induction

    ESS will be entering the competitive, expensive, and lucrative E60 and E63 M5/M6 header market. These headers were designed with the ESS supercharger in mind and will be used on the V2+ and V3 supercharger kits whenever those actually come out. RPI will be carrying these headers which is interesting as they also have a header application for the S85. The difference of course being these are new larger diameter designs with forced induction in mind while all the other headers options available currently are intended for naturally aspirated applications. No word on pricing, but likely not cheap as all S85 headers available are expensive.

    Click here to enlarge

  2. #2
    Join Date
    Jul 2010
    Location
    Encino,CA
    Posts
    8,040
    Rep Points
    5,733.7
    Mentioned
    179 Post(s)
    Rep Power
    58


    Yes Reputation No
    would like some dyno of gains and like to hear how it sounds too! they look like quality pieces
    Burger Motorsports
    Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

    It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.

  3. #3
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    6,684
    Rep Points
    3,343.8
    Mentioned
    226 Post(s)
    Rep Power
    34


    Yes Reputation No
    looks great

  4. #4
    Join Date
    Sep 2010
    Posts
    278
    Rep Points
    146.2
    Mentioned
    1 Post(s)
    Rep Power
    2


    Yes Reputation No
    I don't know about those. Not saying they are bad, but how much do they know about headers? And isn't this very late in the game in relation to the S85?

  5. #5
    Join Date
    Nov 2010
    Location
    le Paris
    Posts
    6,648
    Rep Points
    -164.0
    Mentioned
    48 Post(s)
    Rep Power
    0


    Yes Reputation No
    Click here to enlarge Originally Posted by deemo319 Click here to enlarge
    -how much do they know about headers?
    -And isn't this very late in the game in relation to the S85?
    -Not much. Even EvoSport has better reputation in Headers market, and let SuperSprint aside. they are the best.
    -if they ask a good price for it, they will sell them easily. and also note this headers is for FI cars, no other FI headers were available and it's the first.

  6. #6
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by fastgti69 Click here to enlarge
    would like some dyno of gains and like to hear how it sounds too! they look like quality pieces
    I won't delve into the quality but apparently they are saying these will work great for NA applications too which to me appears they are just trying to sell this to anyone. If these are specifically for forced induction then they will not compare to the quality NA options already on the market that have explored this area. I had custom headers specifically for my forced induction application which provided gains but for NA cars lost power. I don't see how they can do both, they are either for forced induction or not.

  7. #7
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by deemo319 Click here to enlarge
    I don't know about those. Not saying they are bad, but how much do they know about headers? And isn't this very late in the game in relation to the S85?
    I've never seen ESS produce any quality exhaust pieces. This is not to say that they can't but they have demonstrated little to no experience in the area. This is likely outsourced.

  8. #8
    Join Date
    Apr 2010
    Location
    Los Angeles, CA
    Posts
    282
    Rep Points
    245.6
    Mentioned
    1 Post(s)
    Rep Power
    3


    Yes Reputation No
    Click here to enlarge Originally Posted by Sticky Click here to enlarge
    I won't delve into the quality but apparently they are saying these will work great for NA applications too which to me appears they are just trying to sell this to anyone. If these are specifically for forced induction then they will not compare to the quality NA options already on the market that have explored this area. I had custom headers specifically for my forced induction application which provided gains but for NA cars lost power. I don't see how they can do both, they are either for forced induction or not.
    What happened to your headers? Will you still be using them on the new build?
    2009.5 AW E90 335i ZMP - SOLD
    2013 E92 M3 6MT ZCP - Space Grey/Fox Red Click here to enlarge

    Want to Buy: 1977-89 Porsche 911 Turbo Coupe (930)

  9. #9
    Join Date
    Sep 2010
    Posts
    278
    Rep Points
    146.2
    Mentioned
    1 Post(s)
    Rep Power
    2


    Yes Reputation No

    Agreed

    Click here to enlarge Originally Posted by Sticky Click here to enlarge
    I've never seen ESS produce any quality exhaust pieces. This is not to say that they can't but they have demonstrated little to no experience in the area. This is likely outsourced.
    If one has a E63/E64 M6 or an E60 M5, and if you asked around just a little you would end up with a Supersprint headers anyway. They have the know-how and use a proprietary design for the S85 engine. With that world-class engine I would want to attach the best things in the world to it. If you have to ask who made them, that is not a good thing.

  10. #10
    Join Date
    Apr 2010
    Posts
    1,186
    Rep Points
    934.8
    Mentioned
    6 Post(s)
    Rep Power
    10


    Yes Reputation No
    what do you change on a FI header vs a NA header??

  11. #11
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by CookieCrisp Click here to enlarge
    What happened to your headers? Will you still be using them on the new build?
    Yes, I will have a new custom set.

  12. #12
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by MSIZZLE Click here to enlarge
    what do you change on a FI header vs a NA header??
    A lot of things. I'm not super experienced with this so someone else with more knowledge on the subject should chime in. @PEI330Ci is likely a good candidate to answer.

  13. #13
    Join Date
    Feb 2010
    Posts
    2,185
    Rep Points
    2,132.0
    Mentioned
    25 Post(s)
    Rep Power
    22


    Yes Reputation No
    Click here to enlarge Originally Posted by MSIZZLE Click here to enlarge
    what do you change on a FI header vs a NA header??
    I would assume the diameter of the header tubing. Id assume if you go to big on an NA car you will lose lots of torque,if you go to big there wouldnt be enough velocity. I believe a FI car could run bigger tubing because it has the the sc/turbo producing more flow.

    something like this.
    Current:
    14 Viper TA
    Wsir - 1:28:9
    Buttonwillow C13 - 1:54:1

  14. #14
    Join Date
    Apr 2010
    Posts
    4,614
    Rep Points
    3,236.6
    Mentioned
    24 Post(s)
    Rep Power
    33


    1 out of 1 members liked this post. Yes Reputation No
    This subject is extremely complex. Header design for NA cars is much more senitive, cylinder filling and exhaust tuning has a lot to do with primary diameter and length. For forced induction, it is easier to mask poor header design because you have a blower shoving air down the cylinders.

    In NA applications, the headers actually need to be tuned, literally the header length and diameter are specific for your cam and engine. With a blower setup, usually there is less scavenging taking place and you dont necessarily have to tune the headers the same way. For blown applications, bigger is usually better.

    PEI or evolve can give you a better answer.
    Some people live long, meaningful lives.

    Other people eat shit and die.

    I'm not racist, I hate everybody equally; especially fat people.


    Click here to enlarge

  15. #15
    Join Date
    May 2010
    Location
    PEI, Canada
    Posts
    1,123
    Rep Points
    1,665.0
    Mentioned
    30 Post(s)
    Rep Power
    17


    1 out of 1 members liked this post. Yes Reputation No
    Click here to enlarge Originally Posted by Sticky Click here to enlarge
    A lot of things. I'm not super experienced with this so someone else with more knowledge on the subject should chime in. @PEI330Ci is likely a good candidate to answer.
    Click here to enlarge Originally Posted by DBFIU Click here to enlarge
    This subject is extremely complex. Header design for NA cars is much more senitive, cylinder filling and exhaust tuning has a lot to do with primary diameter and length. For forced induction, it is easier to mask poor header design because you have a blower shoving air down the cylinders.

    In NA applications, the headers actually need to be tuned, literally the header length and diameter are specific for your cam and engine. With a blower setup, usually there is less scavenging taking place and you dont necessarily have to tune the headers the same way. For blown applications, bigger is usually better.

    PEI or evolve can give you a better answer.
    You called? Click here to enlarge

    With FI, you don't need to look at the exhaust velocity to tune the header, so you can go with as long and as large (cross section) a header as you like. You still will benefit from pulse tuning though, which is where you get into the length of the primary tubes. In this case, equalizing the path lengths to get a consistent response is a good idea, and running a lower order harmonic tuning order, usually makes this easier. For example, it's easier to make 36" long primaries stay within 5% on "centerline" length, than 24" long primaries. The longer the tube with straight sections, the lower the PLD. (Path length difference) The "centerline" is an average of the top and bottom path lengths...which when calculated correctly, accounts for the actual flow path length inside a tube with bends.

    Looking at the picture, I would guess that ESS has targeted a 2nd order harmonic versus a 3rd order harmonic that you see on most tubular exhaust systems. This means from a N/A perspective that these headers will have a lower peak torque value than a 3rd order header design. Of course it's all a compromise, because any header is "tuned" to a specific RPM point by design, and the efficiency of this design falls off as you go above or below this point. Until someone builds a variable length exhaust header....this will always be the case....
    Rep Points > Posts since 2010

  16. #16
    Join Date
    Sep 2010
    Posts
    289
    Rep Points
    1,038.2
    Mentioned
    225 Post(s)
    Rep Power
    11


    2 out of 2 members liked this post. Yes Reputation No
    Agree with most of what is written (very well I must add) above.

    What's really interesting is when you get into development and testing headers. It's no wonder people call this a black art like I found out years ago. Theories are just theories in this area.

    On our S62 header, we had a MAHA dyno right next to the development room. Everytime we made a change we dyno tested the car. Changes that we thought would work did not.

    We placed alot of emphasis on equal length primaries and found that the engine just did not care after a certain point. We started by making the primaries longer and longer but keeping a small diameter. Power climbed and climbed under the graph area on the first unequal length design. Interestingly peak power did not change much at all from a short unequal length to the long tube (36") but the power under the curve dramatically changed. We then switched to equal length (took ages!) and absolutely nothing happened anywhere in the power range. Equal length of course scrapped because it was almost 1.5 times more expensive to produce. Our final design was not 100% equal length but did have a step up in size in the primaries (known as step design).

    Header design has to be done with testing. You just do not know what is going to work and what will sometimes. Even the best programmes in the world cannot predict everything as we have found out from British motorsport companies.

    With the V10 header alot of companies including ourselves remove the primary CAT's and this gives a staggering different through the rpm range. Supersprint's amazing design goes even further with a cyclic F1 style collector. That one I know was tested very very well. On that one, I would like to see if some changes could be made to go further. We shall find out hopefully!

  17. #17
    Join Date
    May 2010
    Location
    PEI, Canada
    Posts
    1,123
    Rep Points
    1,665.0
    Mentioned
    30 Post(s)
    Rep Power
    17


    Yes Reputation No
    ^^^ Thanks for sharing your real world experience. Most people that do this stuff....don't share.
    Rep Points > Posts since 2010

  18. #18
    Join Date
    Sep 2010
    Posts
    289
    Rep Points
    1,038.2
    Mentioned
    225 Post(s)
    Rep Power
    11


    Yes Reputation No
    Most people don't actually do any testing. They just 'make it'. This is more true within the german tuning industry. Japanese.... that's where lots of testing goes on and they really share it too.

  19. #19
    Join Date
    May 2010
    Location
    PEI, Canada
    Posts
    1,123
    Rep Points
    1,665.0
    Mentioned
    30 Post(s)
    Rep Power
    17


    Yes Reputation No
    Click here to enlarge Originally Posted by evolve Click here to enlarge
    Most people don't actually do any testing. They just 'make it'. This is more true within the german tuning industry. Japanese.... that's where lots of testing goes on and they really share it too.
    This is very much the case in the nitrous industry: Lots of product designed, but very little tested. There are cases where I have learned more about a manufacturers product than they have....from testing.

    Most of exhaust fabricators seem to be more "packaging specialists" than performance specialists....you get what I mean.

    Jere Stahl is a good example of the opposite of this. (Testing junky)
    Rep Points > Posts since 2010

  20. #20
    Join Date
    Jul 2010
    Location
    Encino,CA
    Posts
    8,040
    Rep Points
    5,733.7
    Mentioned
    179 Post(s)
    Rep Power
    58


    Yes Reputation No
    You guys are something else lol. Thanks for the info.
    Burger Motorsports
    Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

    It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.

  21. #21
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by fastgti69 Click here to enlarge
    You guys are something else lol. Thanks for the info.
    Why I love this board, guys like them make this place.

    Great responses gentlemen!

  22. #22
    Join Date
    May 2010
    Location
    PEI, Canada
    Posts
    1,123
    Rep Points
    1,665.0
    Mentioned
    30 Post(s)
    Rep Power
    17


    Yes Reputation No
    I appreciate that Evolve takes the time to share his knowledge extensively. So many great real world examples....

    I look forward to seeing a real world A-B comparison of this product on an FI car.
    Rep Points > Posts since 2010

  23. #23
    Join Date
    Nov 2009
    Location
    la la land
    Posts
    302
    Rep Points
    256.1
    Mentioned
    0 Post(s)
    Rep Power
    3


    Yes Reputation No
    Reserving judgment for the final product. I do like the 1 piece flange, though.

    If they stick with that design then the exhaust note will sound like a V8, though.

  24. #24
    Join Date
    Apr 2010
    Location
    Earth
    Posts
    5,173
    Rep Points
    526.1
    Mentioned
    4 Post(s)
    Rep Power
    6


    Yes Reputation No
    How much are the sc kits?

  25. #25
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    119,483
    Rep Points
    32,156.3
    Mentioned
    2111 Post(s)
    Rep Power
    322



    Yes Reputation No
    Click here to enlarge Originally Posted by GG///M3 Click here to enlarge
    How much are the sc kits?
    http://www.bimmerboost.com/content.p...95-for-the-VT2

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •