Close

Search:

Type: Posts; User: Terry@BMS

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    8
    Views
    205

    Should work fine but keep in mind it would be...

    Should work fine but keep in mind it would be illegal so only do this if it's a competition race use only car.
  2. Replies
    148
    Views
    4,077

    Yes it is possible. But would be expensive to...

    Yes it is possible. But would be expensive to sort out.
  3. Replies
    148
    Views
    4,077

    Run what you want for flash tools but in a few...

    Run what you want for flash tools but in a few weeks that Cobb will be worth a lot less than it was a month ago. Sell high. :)

    MHD and BB are just flash applications. The tuning is done in...
  4. Replies
    148
    Views
    4,077

    You are limited to whatever Cobb has included in...

    You are limited to whatever Cobb has included in their dataset or your DME type. For the most part everything is there but something as simple as disabling a certain fault code or defining another...
  5. Replies
    148
    Views
    4,077

    What can you do in Cobb that you can't in say...

    What can you do in Cobb that you can't in say MHD? I still have that $3k Cobb "pro tuner" license I bought years ago. I've spent plenty of time with it and still use it for the N55 out of necessity....
  6. Replies
    148
    Views
    4,077

    No, that is not true. You can put the JB4 in...

    No, that is not true. You can put the JB4 in bypass mode (map 0) but then with single turbo firmware it will just send 0% duty cycle to your solenoid and not attempt to control boost. If the JB4 is...
  7. Thread: 7.2s 60-130

    by Terry@BMS
    Replies
    1
    Views
    70

    7.2s 60-130

    Hit the private track for a couple runs. Best of which was 7.2s on a less than 1% slope. I reduced boost 4psi in 3rd and it hit DTC in 4th further limiting boost dynamically. Despite that the...
  8. Thread: Wedge Flash

    by Terry@BMS
    Replies
    9
    Views
    415

    The same place we post all of our firmware and...

    The same place we post all of our firmware and flash updates.... :) n54tech.
  9. Thread: Wedge Flash

    by Terry@BMS
    Replies
    9
    Views
    415

    He used to offer a JB4 back end flash map with 15...

    He used to offer a JB4 back end flash map with 15 degrees advance that some liked. It's obsolete now.

    Best bet is our new MHD based back end flash maps with the new 28.8 series JB4 firmware. Much...
  10. Replies
    148
    Views
    4,077

    Were you able to get the JB4 single turbo...

    Were you able to get the JB4 single turbo firmware working for this? Now that you can adjust duty cycle at each RPM and natively log load I think it would make a good fit. :)
  11. Replies
    148
    Views
    4,077

    You are braver than I am! I would never subject a...

    You are braver than I am! I would never subject a build motor to such low octane. :)
  12. Replies
    16
    Views
    338

    All 0 or all 50 to disable. Duty biases effect...

    All 0 or all 50 to disable. Duty biases effect all maps. This is only used when you need to reshape FF relative to PWM.
  13. It can go a bit higher but power doesn't go up...

    It can go a bit higher but power doesn't go up much, and all that heat works against you during longer pulls.
  14. He has an N20 TMAP sensor. With the JB4 and an...

    He has an N20 TMAP sensor. With the JB4 and an N20 TMAP sensor we can control up to 36psi.
  15. Replies
    16
    Views
    338

    Currently 8 is 0%, and 50 is +34%. 0 is around...

    Currently 8 is 0%, and 50 is +34%. 0 is around -8%.

    But it will be adjusted to 0 = 0%, 34 = +34%, shortly.
  16. Hmm I heard otherwise. Attach the dynojet DRF run...

    Hmm I heard otherwise. Attach the dynojet DRF run here and I can check that, and overlay it with these runs, for a comparison. I'm also interested in what the correction factor was in that run.
  17. Nice same car comparison!

    Nice same car comparison!
  18. We stepped them up in boost until power leveled...

    We stepped them up in boost until power leveled off. Then backed down a pound. So at least on the dyno they were moving more massflow. As far as the inlets making the difference I've not seen OEM...
  19. The devil is always in the details on these and...

    The devil is always in the details on these and this 4th gear AT run is legit while the previously claimed record by Wedge was not. I will say if we had our MT with the light weight flywheel & rims...
  20. The dyno runs are plotted by RPM... ? Nothing I...

    The dyno runs are plotted by RPM... ? Nothing I have is anywhere near these boost levels. Our previous record was run at ~21psi tapering to ~16psi IIRC.

    The only good applies to applies...
  21. Replies
    52
    Views
    1,017

    Did you follow the basic recovery directions?...

    Did you follow the basic recovery directions? Unplug battery for a min and then attempt a full write?
  22. Our 482whp WR was using an MT with a light weight...

    Our 482whp WR was using an MT with a light weight flywheel, so the power band isn't really compatible.
  23. Replies
    16
    Views
    338

    I'm not quite sure where you guys have gotten the...

    I'm not quite sure where you guys have gotten the perception that the JB4 has no influence over fuel control when used on top of a flash. That's only true if the flash is targeting the same boost...
  24. Awesome results! MMP intakes & JB4 FTW. :) ...

    Awesome results! MMP intakes & JB4 FTW. :)

    Here are the dyno runs & logs:

    http://www.bimmerboost.com/images/imported/2015/04/attachmentphpattachmentid29198stc1d14280-1.jpg
    ...
  25. Replies
    16
    Views
    338

    I should probably update the JB4 trim scaling to...

    I should probably update the JB4 trim scaling to match what everyone else uses. JB4 logs has it scaled out 33% shows 50 in JB4 logs. Was done to save a floating point calculation and so "high trims"...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4