Close

Search:

Type: Posts; User: Tzu

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    83
    Views
    1,257

    Sort of in the same boat, still deciding which...

    Sort of in the same boat, still deciding which direction I want to go. My issue with hybrids is that they retain the same flawed WG properties, and I NEVER want to hear rattle again ever. I'm leaning...
  2. Doesnt that require the M3 diff and custom length...

    Doesnt that require the M3 diff and custom length driveshaft as well? Might be a saving grave though since I've seen a few diff inputs sheer on the forums.
  3. Replies
    81
    Views
    1,913

    FWIW, my HPFP replaced under recall was giving me...

    FWIW, my HPFP replaced under recall was giving me long cranks after 3yrs, approx 80k km. I just replaced it with the latest 1M pump.
  4. Replies
    20
    Views
    332

    I have no issues with a progressive methanol...

    I have no issues with a progressive methanol system as long as failsafes are in place via piggyback or WG dump, or similar, and tuning is appropriate for the conditions. Direct port is really the...
  5. I dont understand the question? People have been...

    I dont understand the question? People have been doing adaptation resets for YEARS, probablty since 2008. Just reset them and flog the car for a bit and let the DME learn, then log. Don't overthink...
  6. Replies
    203
    Views
    3,914

    I don't on my car. Just loud running noise from...

    I don't on my car. Just loud running noise from the valvetrain. FWIW, I catch about 1/4 cup of oil in my BMS CC over 15k km, mostly highway driving, if thats any indication of my PCV "health".
  7. Replies
    503
    Views
    12,921

    If general principles have taught me anything the...

    If general principles have taught me anything the key to reducing gearbox chatter with a SMFW is to run the thickest possible MT oil, while still being able to maintain adequate lubrication to the...
  8. Replies
    203
    Views
    3,914

    4 in.hg ~ 1.9 PSI, there was probably 8 pounds of...

    4 in.hg ~ 1.9 PSI, there was probably 8 pounds of force sealing that cap to the block. I could see why that would feel unusual. Interesting results T, looking forward to additional testing.
  9. Replies
    21
    Views
    412

    LTFT too, if MHD can do that.

    LTFT too, if MHD can do that.
  10. Replies
    148
    Views
    5,172

    Was just going by the photos. Never hurts to seek...

    Was just going by the photos. Never hurts to seek clarification.
  11. Replies
    21
    Views
    412

    Can you log STFT for both banks? Thats a pretty...

    Can you log STFT for both banks? Thats a pretty big AFR disparity.
  12. Replies
    148
    Views
    5,172

    Is the rear turbo actuator arm touching the...

    Is the rear turbo actuator arm touching the braided coolant line?
  13. Replies
    7
    Views
    135

    Just put the gasket in. IMO, 110k mi between...

    Just put the gasket in. IMO, 110k mi between gasket changes is a reasonable life cycle for rubber components.
  14. Only you guy can argue about nomenclature for 250...

    Only you guy can argue about nomenclature for 250 posts. Point is, upgraded turbos with a free flowing intake = worthwhile.
  15. Replies
    132
    Views
    2,760

    Interesting...I wonder if this is why timing...

    Interesting...I wonder if this is why timing flatline is only half as bad with my oem bin vs canned cobb backend flash.
  16. Whenever you reset adaptations (especially...

    Whenever you reset adaptations (especially throttle), you have to do an ECU reset, and that will prevent the car from getting a bouncing throttle, just a minor issue. I would not enable the sprint...
  17. Replies
    77
    Views
    2,418

    Thats what she said.

    Thats what she said.
  18. Poll: Data and longevity reports is what sells turbo...

    Data and longevity reports is what sells turbo setups. Eager to see your prototype results.
  19. Replies
    203
    Views
    3,914

    Go to harbor freight and grab an analog vacuum...

    Go to harbor freight and grab an analog vacuum gauge; i assume you have lots of hose and NPT fittings. A gauge will run you about $10.
  20. Replies
    132
    Views
    2,760

    Cant open your logs at work, but with that severe...

    Cant open your logs at work, but with that severe timing corrections I'd do a compression test and/or leakdown.
  21. There was a thread on N54tech where a dude was...

    There was a thread on N54tech where a dude was doing exactly this, and posted most of his results.
  22. Replies
    7
    Views
    235

    I wish i logged my startup today from -23*C :)

    I wish i logged my startup today from -23*C :)
  23. Replies
    503
    Views
    12,921

    I'm not so sure about that. I'm fairly certain...

    I'm not so sure about that. I'm fairly certain that the false misfires are caused by increased horsepower screwing with the design harmonics of the original flywheel. With some analysis, I have no...
  24. Thread: Jerky 1st gear

    by Tzu
    Replies
    16
    Views
    488

    I get what you're saying now, but it seems like...

    I get what you're saying now, but it seems like the issue is exacerbated by poor clutch technique. I rarely if ever let off gas in 1st or 2nd from a high enoguh load to let the "according effect"...
  25. Replies
    503
    Views
    12,921

    Agreed. The problem is finding a suitable pairing...

    Agreed. The problem is finding a suitable pairing FW. I wish someone would make an upgraded DMFW, as I'm all for power but want to minimize transmission chatter.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4