Close

Search:

Type: Posts; User: DCAFS

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    14
    Views
    537

    Ahhh...OK I unerstand what you are saying. Shiv...

    Ahhh...OK I unerstand what you are saying. Shiv used the raw pulse outputs of the flow sensor.

    I wish E85 was available in Toronto area......meth is pretty much the only alternative and it keeps...
  2. Replies
    14
    Views
    537

    I'm not so sure that the turbine flow sensor will...

    I'm not so sure that the turbine flow sensor will not work with a piggy.
    Howerton's site states the following:

    "Integration with standalone EMS or Piggy-back systems has never been easier. With...
  3. Replies
    14
    Views
    537

    Reuse my existing pump and solenoid? The...

    Reuse my existing pump and solenoid?

    The vishnu kit already uses the aquamist turbine flow sensor: http://www.howertonengineering.net/hfs-3-4-flowsensor-turbine/
    and their FAV as the solenoid: ...
  4. Replies
    14
    Views
    537

    Right.....requested load versus "actual"...

    Right.....requested load versus "actual" load.....to figure out where you are in the tables according to "actual".

    Looks like Shiv designed the procede to run with stockish load values since I...
  5. Replies
    14
    Views
    537

    Yeah.....it's $#@!ed up and I can't figure it out...

    Yeah.....it's $#@!ed up and I can't figure it out either.

    Flashed back the stock load values in my backend flash and my timing is spot on to where I want it now........post shift is good too!
    ...
  6. Replies
    14
    Views
    537

    Yes....I have tried that load index parameter on...

    Yes....I have tried that load index parameter on the logs and it is always around a value of 80-90 for load.

    Not too sure what to make of that, even stock load is around 130ish.

    I will look in...
  7. Replies
    14
    Views
    537

    Procede logs don't include a logging parameter...

    Procede logs don't include a logging parameter for load as far as I know. I think the OFT does, but I am stacked, so Procede is running the canbus datastream.

    But you raised a good...
  8. Replies
    14
    Views
    537

    Timing exceeding main table values

    Looking for some input as to why my logged timing is hitting 11 degrees advance at 5600 rpm. :think:

    My car typically starts to knock above 10 degrees in this area.....so I capped the main...
  9. Thread: Vargas Bashing

    by DCAFS
    Replies
    30
    Views
    1,450

    Lol....so true! To use an old cliche........ ...

    Lol....so true!

    To use an old cliche........

    "Those who don't learn from history are destined to repeat it"
  10. I wouldn't mind having a look at that too :)

    I wouldn't mind having a look at that too :)
  11. I don't think that Procede can target higher than...

    I don't think that Procede can target higher than 20 psi.......under the user adjustable parameters menu it states a range of overboost limits between 5-20 psi.

    Your log looks good to me but as...
  12. I don't use Cobb.....but I recall someone else...

    I don't use Cobb.....but I recall someone else had this same problem. If I recall correctly there is another separate table where you have to define the breakpoints for the x and y axis first and...
  13. I reduced my meth injector DC down to 70% and it...

    I reduced my meth injector DC down to 70% and it did help reduce the gap in my fuel trims from a 15% variance to less than 10%. But this is with 75F ambients. As ambients drop below 50F the gap...
  14. Lol....funny. I have talked to both by phone...

    Lol....funny.

    I have talked to both by phone and their voices are certainly different.

    Wedge talked to me about for about an hour while Shiv conversations last a few minutes at most.
  15. Don't know about flashing and VIN lock. I just...

    Don't know about flashing and VIN lock.

    I just remember that when I bought the BT cable back when.....it allowed use on 3 different VINS.

    So far I have only used two VINS.....but that may be...
  16. If you need a BT cable let me know as I have one...

    If you need a BT cable let me know as I have one and it still has space for one more vin IIRC.
  17. Hopefully it's just some changes to the torque...

    Hopefully it's just some changes to the torque tables.......keep us posted please.
  18. Thread: GOING INSANE!

    by DCAFS
    Replies
    19
    Views
    829

    Also consider the pressure converter solenoids as...

    Also consider the pressure converter solenoids as well......these control the amount of vacuum being supplied to the wastegate actuator and they have been known to become schizoid.
  19. Tzu.....also another thing. My understanding...

    Tzu.....also another thing.

    My understanding is that as long as the procede boost target is at least 1 psi greater than the DME boost target, then Procede will dictate the target and use it's own...
  20. That's why I changed my original ROM file with...

    That's why I changed my original ROM file with just the basic tables needed.......Timing/AFR/Load.

    When I was messing around with the other Load based tables there seemed to be side effects such...
  21. Yes....I thought that as well.....how could you...

    Yes....I thought that as well.....how could you be hitting 18 psi with a load of only 170?

    Timing tables looked pretty conservative to me as well.

    But I liked the the looks of the throttle...
  22. I had a quick look and compared to my stock IJEOS...

    I had a quick look and compared to my stock IJEOS bin.

    Looks like load values around 170 and very different throttle mapping in the torque request tables......first time I have seen a more linear...
  23. Replies
    15
    Views
    763

    yeah......Ivo warned me about this. People don't...

    yeah......Ivo warned me about this. People don't realize that the valve cover is a very thin plastic material and when we inspect or work on our engines we all tend to lean on it without realizing...
  24. Just a follow up to your issue........ I ran...

    Just a follow up to your issue........

    I ran another datalog today and logged AFR and fuel trims for both banks.

    My trims vary by about 10% between banks, but the AFR's stay within 5% variance...
  25. Log a 3rd gear pull without meth on.....idle is a...

    Log a 3rd gear pull without meth on.....idle is a bit choppy even for me when I watch live data regarding fuel trims....they can breifly be a point or two apart on my car at idle.

    I think a...
Results 1 to 25 of 235
Page 1 of 10 1 2 3 4